As an iconic device in modern high-end bathrooms, the embedded concealed shower set gunmetal is highly favored for its minimalist aesthetic design and excellent performance. Its unique concealed installation method cleverly embeds water pipes and mixing valves into the wall, only revealing the gunmetal showerhead, handheld spray, and control panel. Paired with a gunmetal coating processed by PVD vacuum coating technology, it not only showcases a low-key and luxurious metallic texture but also possesses outstanding corrosion resistance, oxidation resistance, and dirt resistance. The shower sets produced by Usines de robinetterie chinoises, made of high-quality brass or stainless steel materials and precisely processed to meet international standards, also offer customized services and are widely used in various high-end places. The following is a detailed installation guide to help you complete the installation smoothly.
(I) Précautions à prendre avant l'installation du produit
Before starting the installation of the embedded concealed shower set gunmetal, carefully read the product manual to familiarize yourself with the functions of each component and installation requirements. At the same time, confirm the structure of the bathroom wall. Load-bearing walls or solid brick walls are ideal choices. If it is a non-load-bearing structure such as a hollow wall, additional reinforcement measures may be required. In addition, understand the water pressure at home and ensure it is within the applicable range of the product (usually 0.1 – 0.5MPa). Excessively high or low water pressure may affect the usage effect.
(II) Outils d'installation nécessaires
A series of professional tools are needed for the installation process, mainly including an electric drill, wrenches (including adjustable wrenches and socket wrenches), a spirit level, a tape measure, Teflon tape, silicone, a pipe wrench, etc. The electric drill is used to drill holes in the wall; wrenches are used to tighten or loosen pipe fittings and screws; the spirit level ensures the levelness of the installation; the tape measure is used for precise measurement and positioning; Teflon tape and silicone are used to seal joints to prevent water leakage; and the pipe wrench is used to grip and rotate pipe fittings.
(III) Étapes de préparation avant l'installation
First, turn off the main water supply valve at home to avoid water spraying during the installation process. Then, empty the remaining water in the pipes by turning on other faucets and letting the water run for a few minutes. Next, accurately mark the installation positions of the water pipes, mixing valves, and other components on the wall according to the product manual. Use a tape measure and a spirit level during measurement to ensure the positions are accurate, with an error controlled within ±2mm. If holes need to be drilled in the wall, confirm in advance that there are no obstacles such as wires and other pipes at the drilling positions.
(IV) Processus d'installation standard
Use an electric drill to drill holes in the wall according to the marked positions. The diameter and depth of the holes must strictly meet the product requirements. Embed the water pipes and mixing valves into the wall, calibrate with a spirit level to ensure the mixing valve is in a horizontal state, and then fix them firmly with expansion bolts or screws. When connecting the cold and hot water pipes, pay attention to distinguish the cold and hot water interfaces (usually hot on the left and cold on the right) and wrap enough Teflon tape (usually 8 – 10 turns) to prevent water leakage. Install the gunmetal showerhead, handheld spray, and control panel in their corresponding positions, tighten the screws to ensure a tight connection. If necessary, apply an appropriate amount of silicone to enhance the sealing.
(V) Key Points of Use Testing and Inspection
After the installation is completed, slowly open the main water supply valve and check whether there are any water leakage phenomena at each joint. Pay special attention to the connections of water pipes, the interfaces of mixing valves, and the connections of the showerhead and spray. Conduct a water pressure test and observe whether the water flow is stable and whether the water output of the overhead showerhead and handheld spray is uniform. Check whether the multi-functional water flow control valve and the thermostatic mixing system can adjust the water flow and water temperature normally. During the test process, record various parameters, such as the size of the water flow and the range of water temperature changes, to ensure they meet the product standards.
(VI) Problèmes d'installation courants et solutions
If water leakage is found at the joint, it may be due to insufficient or uneven winding of the Teflon tape. Turn off the water source, rewind the Teflon tape, and then make the connection again. If the water leakage is severe, it may be that the pipe fittings are damaged, and new pipe fittings need to be replaced in a timely manner. If the water flow is unstable or the water output is blocked, it may be that there are impurities blocking the pipeline. Remove the spray and water pipes and rinse the pipeline with a high-pressure water gun. It may also be a water pressure problem, so contact a professional to check and adjust the water pressure.
(VII) Conseils de sécurité et suggestions d'entretien
During the installation process, ensure that the power supply is turned off to avoid the risk of electric shock. When using tools such as electric drills, strictly follow the operating procedures to prevent accidental injuries. In daily use, regularly clean the surface of the gunmetal coating by wiping it with a soft damp cloth. Avoid using steel wool, corrosive cleaning agents, etc., to prevent damage to the coating. Check every six months whether the connections of each component are loose and whether the sealing is good. Reinforce and replace aging components in a timely manner to extend the service life of the embedded concealed shower set gunmetal.
